Measure voltage, current and resistance with a multimeter

Learn to use the most useful tool on any electronics bench. You measure the voltage of the UNO and a 9 V battery, find out where the voltage goes in an LED circuit, measure the current, check resistors and test...
  • Level:Beginner
  • Duration: 45 min
  • Ages 8+
  • Platform: Arduino

Tools for this lesson

Helpful for this build. Open a tool to see tips and more projects that use it.

Measure voltage, current and resistance with a multimeter – EEMENTOR STEM™ lesson

When a circuit doesn't work, guessing is slow. Measuring is fast. A multimeter is the tool electronics engineers reach for first: with two probes and a dial, it tells you the voltage between two points, the current flowing through a wire and the resistance of a part. In this lesson you build a simple LED circuit and measure everything in it. You'll see where the 5 V of the UNO goes, how much current the LED really uses, and whether that resistor is really 220 Ω. Like every lesson in this path, there is no program to write: the UNO is only the power supply.

What you'll learn

  • How to set up a multimeter: which socket and which setting for each job
  • How to measure voltage across a part, and why the voltages in a loop add up
  • How to measure current by putting the meter in the circuit
  • How to measure resistance, and test wires with the continuity beeper
  • The one mistake that blows a multimeter's fuse, and how to avoid it

What you need

  • UNO R3 board and USB cable (UNO R3 Starter Kit)
  • 1 red LED (UNO R3 Starter Kit)
  • 2 resistors: 220 Ω (red, red, brown) and 10 kΩ (brown, black, orange) (UNO R3 Starter Kit)
  • 9 V battery (UNO R3 Starter Kit)
  • Breadboard and jumper wires (UNO R3 Starter Kit)
  • A digital multimeter. Any basic one works; it is not in the kit. No meter yet? Do every experiment in EEMENTOR Lab, which has a multimeter that works like a real one, for free.

Meet the multimeter

A multimeter has a screen, a dial and two probes, red and black. The black probe always goes in the socket marked COM (common). The red probe goes in the socket marked V Ω mA for almost everything. Some meters also have a separate 10 A socket for large currents; you won't need it in this lesson.

Turn the dial to what you want to measure: V⎓ (DC volts, a straight line with dashes under it), mA (milliamps), Ω (ohms) or the beeper symbol (continuity). If your meter has number ranges such as 20 V or 200 mA, pick the first range bigger than what you expect. An "auto-ranging" meter picks the range by itself.

The golden rule: in mA mode the meter is almost a plain wire. Never touch the probes across a battery or between 5V and GND in mA mode: that makes a short circuit through the meter and blows its fuse. Before you measure volts, always check the dial is back on V.

Wiring

Build a simple LED circuit: the UNO's 5V goes to the red (+) rail, GND to the blue (−) rail, and a 220 Ω resistor and a red LED sit in a row between them. The LED's long leg (+) points towards the resistor.

Breadboard wiring diagram: UNO 5V to the plus rail and GND to the minus rail, with a 220 ohm resistor and a red LED in a row between them.
Breadboard view. Check each connection against the wiring table below.
From To
UNO 5V The red (+) rail
UNO GND The blue (−) rail
The red (+) rail 220 Ω resistor
220 Ω resistor, other end LED long leg (+)
LED short leg (−) The blue (−) rail
FREE

Build this circuit in EEMENTOR Lab

Wire it yourself in your browser before you touch a real wire. No sign-up, nothing to install.

The UNO and the parts for this lesson laid out in EEMENTOR Lab, ready to wireBuild it yourself
  1. The UNO and this lesson’s parts are already placed. Wire them using the wiring table above. Pins with no wire show red.
  2. Missing a part? Add it from the parts list on the left.
  3. Press Run, then click Multimeter above the drawing and do the experiments: across the resistor, across the LED, and in a gap for the current.

EEMENTOR Lab is free and in beta. Results are a guide; a real build can differ slightly. About the Lab

Try it

Experiment 1: measure a voltage

  1. Plug the UNO's USB cable in. The LED lights.
  2. Turn the dial to V⎓ (20 V range if your meter has ranges).
  3. Touch the black probe to the blue (−) rail and the red probe to the red (+) rail. The screen shows about 5 V. Anything from about 4.7 to 5.1 V is normal: USB power isn't exactly 5 V.
  4. Swap the probes. The number gets a minus sign: the meter tells you the red probe is now at the lower voltage.
  5. Measure the 9 V battery on its own: black on −, red on +. A new battery often shows a little more than 9 V.

Experiment 2: find out where the voltage goes

  1. Keep the dial on V⎓. Touch the probes to the two legs of the resistor. It shows about 3 V.
  2. Now touch them to the two legs of the LED. It shows about 2 V.
  3. Add the two numbers: they make the 5 V you measured in experiment 1. The voltage of the supply is shared out between the parts in the loop. Engineers call this Kirchhoff's voltage law.

Experiment 3: measure the current

  1. Unplug the USB cable. Move the red probe to the mA socket if your meter has a separate one, and turn the dial to mA (200 mA range).
  2. Pull the LED's long leg out of its hole, so there is a gap between the resistor and the LED.
  3. Touch the red probe to the resistor's end and the black probe to the LED's long leg. The current now has to flow through the meter.
  4. Plug the USB cable in. The LED lights again and the screen shows about 13 to 15 mA.
  5. Unplug the USB cable, put the LED's leg back, turn the dial back to V and move the red probe back to the V socket.

Experiment 4: measure resistance and test for breaks

  1. Resistance is measured with the power off, on a part that is out of the circuit. Turn the dial to Ω.
  2. Hold the probes on the two legs of the loose 220 Ω resistor. The screen shows a number close to 220. Its gold band means "within 5 %", so anything from 209 to 231 Ω is fine.
  3. Measure the 10 kΩ resistor. A meter with ranges may need the 20 kΩ range. Don't hold both legs with your fingers: your body is a resistor too, and it changes the reading.
  4. Turn the dial to the beeper symbol. Touch the probes to the two ends of a jumper wire: it beeps, so the wire is good. Touch two holes in the same breadboard row: beep. Two holes in different rows: silence.

What you should see

Table of typical readings: about 5 V from the UNO, a little over 9 V from a new battery, about 3 V across the resistor and 2 V across the LED, 13 to 15 mA, 209 to 231 ohms, 9.5 to 10.5 kilohms, and a beep for a good wire.
Typical readings. Yours will be close to these, not exactly the same.

How it works

How to hold the probes: across the LED for voltage, in a gap between the resistor and the LED for current, and on a loose resistor with the power off for resistance.
Across for volts, in the gap for amps, on its own for ohms.

Voltage is the push between two points, so you always measure it between two points: the probes go across a part, side by side with it (in parallel). The meter takes almost no current, so it doesn't change the circuit. In a loop, the pushes across all the parts add up to the push of the supply: about 2 V for the red LED and about 3 V for the resistor.

Current is how much electricity flows past one point, so the meter has to sit in the path, in a gap you make (in series). Inside, the mA setting is a very small resistor, which is why it acts like a wire and why it must never go straight across a battery. You can even check the reading with Ohm's law: the resistor has about 3 V across it, and 3 V ÷ 220 Ω ≈ 0.014 A, or 14 mA.

Resistance is measured with the meter's own tiny battery. It pushes a small current through the part and measures how hard that is. If the circuit's power is on, or other parts are connected, they mix up that measurement, so the part must be on its own with the power off. Continuity is the same idea with a beep instead of a number: very low resistance means "connected".

Try this next

  • Swap the 220 Ω resistor for the 10 kΩ one and measure again. Predict the current with Ohm's law first, then check it.
  • Measure the voltage of the 9 V battery while it lights an LED through a 220 Ω resistor, and compare it with the voltage on its own.
  • Practise in EEMENTOR Lab: measure the voltage across an LED and measure the current. The Lab's examples use a 330 Ω resistor, so the numbers are a little different.
  • Go back to series and parallel circuits and measure the voltages and currents there.

Troubleshooting

  • The screen shows 0 or nothing in mA mode: the red probe is in the V socket, the circuit isn't open (the meter must be in the gap), or the meter's fuse has blown after a short circuit.
  • The screen shows "OL" or "1" on the left: the value is bigger than the range, or the probes aren't touching anything. Choose a bigger range, or press the probes on firmly.
  • The voltage reading jumps around: the probe tips aren't touching metal. Press them on the bare legs or into the rail holes.
  • The resistance is far from the colour code: make sure the power is off and the resistor is out of the circuit, and that your fingers aren't touching both legs.
  • The LED doesn't light at the start: turn it round. The long leg (+) must point towards the resistor and the 5V rail.