ESP32 starter kit buying guide 2026: 7 kits compared

A fair comparison of seven ESP32 starter kits: which chip each uses, which languages the tutorials cover, and which kit suits which kind of learner.
  • Level:Beginner
  • Duration: 15 min
  • Ages 12+
  • Platform: ESP32

What you'll need

Tools for this lesson

Helpful for this build. Open a tool to see tips and more projects that use it.

ESP32 starter kit buying guide 2026 – EEMENTOR STEM™ guide

Quick answer: the best ESP32 starter kit is the one whose tutorials match how you want to learn. Pick a kit with MicroPython or Scratch lessons if you don't want to write C++ yet, an ESP32-S3 board if you want the newer chip and a camera interface, and a kit with Arduino IDE lessons that go all the way to cloud dashboards and phone apps if your goal is IoT projects. Below we compare seven popular kits fairly, including our own, using only facts from each maker's official pages.

What you need

  • A computer with Windows, macOS or Linux and the free Arduino IDE (every kit below supports it)
  • An idea of what you want to build: smart home, sensors, robots, a camera or cloud dashboards
  • To try the test sketch in this guide: any ESP32 board, a USB cable, 1 LED, 1 resistor (220 Ω) and 2 jumper wires. All of these are in our ESP32 IoT Starter Kit

Steps: how to choose an ESP32 starter kit

  1. Choose the chip. The classic ESP32 has Wi-Fi and both Bluetooth Classic and Bluetooth LE. The ESP32-S3 is newer, with Wi-Fi and Bluetooth LE 5 but no Bluetooth Classic. For learning Wi-Fi and IoT, both are excellent.
  2. Choose the language. Arduino C/C++ has the most examples online. MicroPython is easier to read for some beginners. Scratch-style blocks suit younger learners.
  3. Check the tutorials before you buy. Good makers put them online for free. Open a lesson and see whether the wiring pictures and explanations make sense to you.
  4. Check the parts against the projects you want. A relay and a DHT11 for smart home, a servo and motor driver for movement, a display for readouts.
  5. Check how the board fits. ESP32 boards are wide. Most kits add an expansion or breakout board so you still have free holes on the breadboard.
Checklist of 5 questions to ask before buying an ESP32 kit: which chip, which language, how good the tutorials are, whether the parts fit your projects, and whether the board fits the breadboard.
The five steps above as a checklist you can use for any kit.

7 ESP32 starter kits compared

Facts come from each maker's own product and tutorial pages in November 2026. Kits change, so check the maker's page before you buy.

Kit Board Tutorial languages Good to know
EEMENTOR ESP32 IoT Starter Kit (ours) ESP32-DevKitC V4 (ESP32-WROOM-32) with an expansion board Arduino C/C++ 110+ free step-by-step lessons online in a learning path, from the first LED to Wi-Fi web pages, Blynk, Arduino Cloud, Google Sheets and phone alerts.
Freenove Ultimate Starter Kit for ESP32 (FNK0047) Freenove ESP32-WROVER board with a camera interface, plus an extension board C (Arduino IDE), Python, Processing Tutorials and code are free to download from GitHub.
Freenove Ultimate Starter Kit for ESP32-S3 (FNK0082) ESP32-S3-WROOM-1 board with a camera interface, plus an extension board C (Arduino IDE), Python, Processing Same tutorial style as the WROVER kit, on the newer S3 chip.
SunFounder ESP32 Starter Kit ESP32 WROOM 32E, on a camera extension board with an OV2640 camera and microSD slot Arduino, MicroPython, Scratch (PictoBlox) The widest choice of languages here. Parts include an I2C LCD1602, a WS2812 LED strip, soil moisture sensor and a small water pump.
ELEGOO ESP-32 Super Starter Kit ESP-32 board Online tutorial Listed on ELEGOO's official store with a download centre entry. We couldn't open the full product page to confirm the parts list.
Keyestudio ESP32 Learning Kit Basic Edition (KS5012) Mini board based on ESP-WROOM-32 Arduino, Python (MicroPython), C on Raspberry Pi 74 project tutorials across the three tracks. Includes a battery holder.
LAFVIN Basic Starter Kit for ESP32-S3 ESP32-S3-WROOM C (Arduino IDE), Python Free online tutorial with camera web server chapters; code on GitHub.
Comparison of the classic ESP32 and the ESP32-S3: both are dual-core up to 240 MHz with 2.4 GHz Wi-Fi; only the classic ESP32 has Bluetooth Classic; only the S3 has native USB.
Chip facts from Espressif. Both chips are a good choice for Wi-Fi and IoT projects.

Which kit suits whom

  • You want to start without C++: SunFounder (MicroPython and Scratch) or Keyestudio (MicroPython).
  • You want the newer ESP32-S3 and camera projects: Freenove ESP32-S3 or LAFVIN ESP32-S3.
  • You want Python as well as C, with free GitHub code: either Freenove kit.
  • You want a guided IoT path in the Arduino IDE: our ESP32 IoT Starter Kit. Its lessons build up to Wi-Fi control, cloud dashboards and phone notifications. It doesn't include MicroPython lessons or a camera-ready board.

Full code: a 2-minute test for any ESP32 kit

Whichever kit you choose, run this first. It blinks an LED and lists the Wi-Fi networks around you, so you know the board, the USB connection and the Wi-Fi radio all work. It runs on the classic ESP32 and on the ESP32-S3.

// ESP32 kit test: blink an LED and scan for Wi-Fi networks.
#include <WiFi.h>

const int LED_PIN = 4;   // GPIO 4 works on classic ESP32 and ESP32-S3 boards

void setup() {
  Serial.begin(115200);
  pinMode(LED_PIN, OUTPUT);
  WiFi.mode(WIFI_STA);   // station mode: look for networks
  WiFi.disconnect();
  delay(100);
  Serial.println("ESP32 kit test started");
}

void loop() {
  digitalWrite(LED_PIN, HIGH);
  Serial.println("Scanning for Wi-Fi networks...");
  int count = WiFi.scanNetworks();
  digitalWrite(LED_PIN, LOW);

  if (count == 0) {
    Serial.println("No networks found");
  } else {
    Serial.print(count);
    Serial.println(" networks found:");
    for (int i = 0; i < count; i++) {
      Serial.print("  ");
      Serial.print(WiFi.SSID(i));
      Serial.print("  (");
      Serial.print(WiFi.RSSI(i));
      Serial.println(" dBm)");
    }
  }
  WiFi.scanDelete();   // free the memory used by the results
  delay(5000);
}

To upload it, add ESP32 support to the Arduino IDE first. Our lesson Set up the ESP32 in the Arduino IDE shows each step.

Serial Monitor at 115200 baud showing the kit test: a start message, then a list of nearby Wi-Fi networks with their signal strength in dBm, repeating every few seconds.
What the test sketch prints. Your network names and numbers will be different.

Wiring

Breadboard wiring diagram: ESP32 GPIO 4 to a 220 Ω resistor and a red LED, with the LED short leg to GND.
Breadboard view. Check each connection against the wiring table below.
From To
ESP32 GPIO 4 220 Ω resistor, then the LED's long leg
LED short leg ESP32 GND

ESP32 pins work at 3.3 V. Never connect a 5 V signal straight to a GPIO pin; use a level shifter or a voltage divider for 5 V sensors.

FREE

Build this circuit in EEMENTOR Lab

Wire it yourself in your browser before you touch a real wire. No sign-up, nothing to install.

The ESP32 and the parts for this lesson laid out in EEMENTOR Lab, ready to wireBuild it yourself
  1. The ESP32 and this lesson’s parts are already placed. Wire them using the wiring table above. Pins with no wire show red.
  2. Not in the Lab yet: camera. Build the rest of the circuit without it.
  3. Press Run, then try the inputs: click, hold or slide them under Selected.
  4. Wi-Fi and Bluetooth don’t run in the Lab yet, so use it to build the circuit and check the wiring before you upload the real sketch.

EEMENTOR Lab is free and in beta. Results are a guide; a real build can differ slightly. About the Lab

Common problems

  • "Failed to connect to ESP32" when uploading: hold the BOOT button while the IDE shows "Connecting…", then release it.
  • No port appears: try a different USB cable, as some only charge. Your board may need a USB driver for its USB chip (for example CH340, CH343 or CP2102); the maker's tutorial names the chip.
  • Garbled text in the Serial Monitor: set the speed to 115200 baud.
  • "0 networks found": the ESP32 only sees 2.4 GHz Wi-Fi. A 5 GHz-only router won't appear.
  • The board resets when Wi-Fi starts: Wi-Fi draws bursts of current. Use a good USB port or a powered hub.

FAQ

Is an ESP32 kit or an Arduino UNO kit better for beginners?

Both work. The UNO runs at 5 V and has the most beginner tutorials, which makes the first steps very gentle. The ESP32 adds Wi-Fi and Bluetooth, so it's the better choice if you want internet and phone projects soon. See our UNO R3 Starter Kit if you'd rather start with the UNO.

Should I choose ESP32 or ESP32-S3?

For learning Wi-Fi and IoT, either is fine. The S3 is newer and has native USB, while the classic ESP32 also supports Bluetooth Classic and has the most examples online.

Can I use MicroPython with the EEMENTOR ESP32 IoT Starter Kit?

The ESP32 board can run MicroPython firmware, but our lessons are written for the Arduino IDE in C/C++. If MicroPython lessons matter most to you, a kit with a MicroPython track is the better fit.

Do ESP32 kits work with 5 V sensors?

Many sensors in these kits run on 3.3 V. For a sensor that outputs 5 V, such as some ultrasonic modules, reduce its signal with a voltage divider or a level shifter before it reaches a GPIO pin.

What can I build with an ESP32 starter kit?

Typical first projects are a Wi-Fi controlled relay, a web page that moves a servo, a temperature logger and motion alerts on your phone. Our ESP32 IoT starter path lists every project with free instructions.

Related lessons